Fabrikant: LSL Referentie: 280-721L
LSL Kentekenplaathouder Mantis-RS | Kawasaki Z1000
KAWASAKI Z1000 2014-2020, Z1000SX 2014-2019
€ 79,95
Incl. BTW
Vraag om prijs of meer informatie
close
3-5 werkdagen
Op vooraad magazijn Duitsland
Beschrijving
LSL license plate holder MANTIS-RS
Making good bikes perfect. Following this motto, LSL has developed the license plate holder MANTIS-RS.
It fits perfectly to your motorcycle and underlines the lines of your bike with its sporty design.
And as usual from LSL, one has thought of everything.
The model-specific bracket of the MANTIS-RS allows replacement without further drilling or cutting on the vehicle.
The design fits perfectly to the rear of your motorcycle, using the original mounting points of the vehicle.
Against damage to the cables, sharp-edged feedthroughs are protected with rubber membrane grommets.
The license plate is made of 2 mm thick sheet steel, laser-cut, edged and weather-resistant black powder-coated.
The fixing of the license plate in the correct position is done by an additional locking screw.
The width-adjustable turn signal brackets of the MANTIS-RS are suitable for any type of accessory turn signal. This adjustment option allows you to find the right position for your turn signals. The adaptation to the most different EU license plates is therefore no problem. The mounting holes of the turn signals have a diameter of 10 mm and are slotted to the side. This makes it possible to mount the turn signals without disconnecting them from the wiring harness.
Also the slider for the attachment of the rear reflector is individually adjustable. An adaptation to the different designs of the EU license plates is therefore no problem.
The two rubber washers supplied are used for the vibration-reducing screw connection of the license plate. An additional rubber buffer supports the license plate on the underside.
Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European number plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixing without further work steps (e. g.B. Drilling)
- easy mounting of the license plate through slotted holes
The scope of delivery of the MANTIS-RS includes:
- Model-specific bracket with mounting parts
- MANTIS-RS license plate retaining plate
- Adjustable turn signal holders
- E-tested reflector with adjustable holder
- Mounting instructions
Note:
The special turn signal holder 280-974 is optionally available for the original turn signals.
Tip:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from LSL, which are available in many different designs, are certainly a good alternative.
Making good bikes perfect. Following this motto, LSL has developed the license plate holder MANTIS-RS.
It fits perfectly to your motorcycle and underlines the lines of your bike with its sporty design.
And as usual from LSL, one has thought of everything.
The model-specific bracket of the MANTIS-RS allows replacement without further drilling or cutting on the vehicle.
The design fits perfectly to the rear of your motorcycle, using the original mounting points of the vehicle.
Against damage to the cables, sharp-edged feedthroughs are protected with rubber membrane grommets.
The license plate is made of 2 mm thick sheet steel, laser-cut, edged and weather-resistant black powder-coated.
The fixing of the license plate in the correct position is done by an additional locking screw.
The width-adjustable turn signal brackets of the MANTIS-RS are suitable for any type of accessory turn signal. This adjustment option allows you to find the right position for your turn signals. The adaptation to the most different EU license plates is therefore no problem. The mounting holes of the turn signals have a diameter of 10 mm and are slotted to the side. This makes it possible to mount the turn signals without disconnecting them from the wiring harness.
Also the slider for the attachment of the rear reflector is individually adjustable. An adaptation to the different designs of the EU license plates is therefore no problem.
The two rubber washers supplied are used for the vibration-reducing screw connection of the license plate. An additional rubber buffer supports the license plate on the underside.
Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European number plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixing without further work steps (e. g.B. Drilling)
- easy mounting of the license plate through slotted holes
The scope of delivery of the MANTIS-RS includes:
- Model-specific bracket with mounting parts
- MANTIS-RS license plate retaining plate
- Adjustable turn signal holders
- E-tested reflector with adjustable holder
- Mounting instructions
Note:
The special turn signal holder 280-974 is optionally available for the original turn signals.
Tip:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from LSL, which are available in many different designs, are certainly a good alternative.
KAWASAKI Z1000 2014-2020, Z1000SX 2014-2019
Specificaties
Kleur | Zwart |
---|---|
Materiaal | Staal |
0/5
chat
Commentaar (0)
error Je beoordelingswaardering kan niet worden verzonden
feedback Rapporteer reactie
Ben je zeker dat u deze opmerking wil rapporteren?
fa-envelope Melding verzonden
Je opmerking is ingediend en zal door een beheerder worden behandeld.
error Je opmerking kan niet worden verzonden
Schrijf je recensie
fa-envelope Beoordeling verstuurd
Je beoordeling is toegevoegd en wordt beschikbaar zodra deze is goedgekeurd.
error Je beoordeling kan niet worden verzonden